Sitecom WLM-1500 Bedienungsanleitung

WLM-1500/2500/3500 Wireless ADSL2+ Modem Router

7 PC Network Adapter setup Windows XP • Go to [Start Menu],  [Control panel],  [Network Connections]. • Right-mouse-click on the [Local Area C

Windows Vista/Windows 7 • Go to [Start Menu],  [Control panel],  [View network status and tasks], -> [Manage network connections]. • Righ

• Select [Internet Protocol Version 4 (TCP/IPv4)], and Click [Properties]. • Open the [General] tab. The WLM-1500/2500/3500 supports DHCP.

8 Bring up the WLM-1500/2500/3500 Connect the supplied power-adapter to the power inlet port and connect it to a wall outlet. Press the Power-Button

Status The System status section allows you to monitor the current status of your router: the UP time, hardware information, seria

Statistics You can view statistics on the processing of IP packets on the networking interfaces. You will not typically need to v

ADSL Statistics This page shows the ADSL line statistic information.

DHCP List This page shows all DHCP clients (LAN PCs) currently connected to your network. The table shows the assigned IP address, MAC add

QoS Queue The screen allows you to configure a QoS queue and assign it to a specific network. If the channel operation modes of your ADSL router

10 Configuration Wizard Click Wizard to configure the modem. The Setup wizard will now be displayed; check that the adsl line is connected and clic

2 User Manual TABLE OF CONTENTS 1 KEY FEATURES ...

11 Basic Settings LAN Settings This page is used to configure the LAN interface of your ADSL Router. You can set IP address, subnet mask, and IGMP

DHCP Settings You can configure your network and the router to use the Dynamic Host Configuration Protocol (DHCP). This page allows you to select

Parameter Description DHCP Server Address Specify the IP address of your ISP’s DHCP server. Requests for IP information from your LAN interface wi

IP Pool Range You can select a particular IP address range for your DHCP server to issue IP addresses to your LAN Clients. By default, the IP range

WAN Settings The page allows you to select any combination of DSL modes. Parameter Description ADSL modulation Choose preferred ADSL standard

settings will take effect after it reboots. DNS A Domain Name System (DNS) server is like an index of IP addresses and Web addresses. If you type a

Wireless Settings This section provides the wireless network settings for your router. You can enable the wireless AP function here. Parameter

802.11g, and 802.11n wireless network client to connect this router (maximum transfer rate 11Mbps for 802.11b clients, maximum 54Mbps for 802.11g cli

Security This router provides complete wireless LAN security functions, include WEP, IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key and

by a RADIUS server. Check this box to authenticates user by IEEE 802.1x. WEP-64Bits WEP is less level of security than WPA. WEP supports 64-bit and

Introduction Congratulations on your purchase of the WLM-1500/2500/3500 Wireless ADSL2+ Modem. The WLM-1500 uses technology based on 802.11n, while

ACL This wireless router supports MAC Address Control, which prevents unauthorized clients from accessing your wireless network. Par

button. Click "Reset" will clear your current selections. When you finish, click ‘Apply Changes’. You’ll see the following message display

WPS Although home Wi-Fi networks have become more and more popular, users still have trouble with the initial set up of network. This obstacle for

Regenerate PIN Click to regenerate the Self-PIN Number. Push Button Configuration Clicking this button will invoke the PBC method of WPS. It is only

12 Advanced Settings Wireless Settings This page allows advanced users who have sufficient knowledge of wireless LAN. These setting shall not

the WEP privacy mechanism. Auto: Auto is the default authentication algorithm. It will change its authentication type automatically to fulfill clien

protection mode is enabled, the throughput of the AP will be a little lower due to many of frame traffic should be transmitted. Aggregation This fun

QoS The router supports IP QoS feature that can provide different priority to different users or data flows. Classification Parameter Descripti

(Destination) destination IP has been entered. Port (Destination) The destination port of the selected protocol. You cannot configure this field wi

UPnP When the UPnP function is enabled, the router can be detected by UPnP compliant system such as Windows XP. The router will be displayed in the

1 Key Features Features Advantages IEEE 802.11g compliant Fully Interoperable with IEEE 802.11b / IEEE802.11g compliant devices Based on 802.11n

IGMP The IGMP Proxy page allows you to enable multicast on WAN and LAN interfaces. The LAN interface is always served as downstream IGMP proxy, and

Routing The page enables you to define specific route for your Internet and network datas. Most users do not need to define routes. On a typical sm

Show Routes Click this button to view the router’s routing table. Static Route Table Click “Update” to update the selected destination route on the

SNMP Simple Network Management Protocol (SNMP) is a troubleshooting and management protocol that uses the UDP protocol on port 161 to communicate be

Press ‘Continue’ to save the settings made and back to web management interface; press ‘Apply’ to save the settings made and restart the router so

DDNS Dynamic DNS (DDNS) allows you to map the static domain name to a dynamic IP address. You must get an account, password and your static domain n

Press ‘Continue’ to save the settings made and back to web management interface; press ‘Apply’ to save the settings made and restart the router so

RIP RIP is an Internet protocol you can set up to share routing table information with other routing devices on your LAN, at your ISP’s location, or

passed to the DSL device in order for it to be accepted into its routing table. Send Mode Indicate the RIP version this interface will use when it s

13 Firewall Settings The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of h

2 Package Contents Open the package carefully, and make sure that none of the items listed below are missing. Do not discard th

Public Port The destination port number that is made open for this application on the WAN side Interface Select the WAN interface on which the port

Port Filter The IP/Port filtering feature allows you to deny/allow specific services or applications in the forwarding path. Parameter Descript

Address. Port LAN users use port number to distinguish one network application over another such as 21 is for FTP service. The port number range is

MAC Filtering The MAC filtering feature allows you to define rules to allow or deny frames through the router based on source MAC address, destinati

Destination MAC Address The destination MAC address. It must be 12-digit hexadecimal format, for example: “00-d0-59-c6-12-50”. Current Filter Table I

URL Blocking This page is used to block some URL addresses or keywords. Parameter Description URL Blocking Enable or disable the URL blockin

Press ‘Continue’ to save the settings made and back to web management interface; press ‘Apply’ to save the settings made and restart the router so t

ACL Configuration The Access Control List (ACL) is a list of permissions attached to the router. The list specifies who is allowed to access this ro

DMZ The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP Address as the DMZ Host, all incoming packets wi

14 TOOLBOX Settings Password This page allows you to set the password to access the web server of the router. Please select the “admin (as admin

3 Product Layout Port Description ADSL Connect your telephone/ADSL cable this port LAN Connect the cable from your PC or network

It means the content in ‘Current Password’ field is wrong, please click ‘OK’ to go back to previous menu, and try to input current password again.

Time Zone The Time Zone allows your router to set its time; especially for recording System Log. Parameter Description Current Time The current

Remote Access The Remote Access function can secure remote host access to your router from LAN and WAN interfaces for some services provided by the

Press ‘Continue’ to save the settings made and back to web management interface; press ‘Apply’ to save the settings made and restart the router so th

Configuration Tools This page allows you to backup the current settings to a file or restore the settings from the file which was saved previously.

Reboot Whenever you use the Web configuration to change system settings, the changes are initially placed in temporary storage. To save your change

Diagnostics Ping Once you have your router configured, you can send a ping command to the host you specify in this page. To use it, you must know

Diagnostic Test The Diagnostic Test page shows the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN s

Back label The back label describes the corresponding LED indications and port functionality. LED Description Power Lights up when powered ON. Bli

4 System Requirements To begin using the WLM-1500/2500/3500, make sure you meet the following as minimum requirements: • PC/Notebook. • 1 Free Et

6 Setup LAN, WAN Modem connection LAN / computer connections